Heavy-Duty Black Metal Garden Rack – Strong Storage Organizer for Tools, Hoses & Supplies, Keeping Outdoor Spaces Clutter-Free

Reach for the rake and get the rake

Long handles leaned in a corner are a stack waiting to go. You pull the hoe out from the middle, three others slide, and the whole lot comes down — usually across the mower, sometimes across your shin.

The fix is not tidying. It is giving every handle a slot of its own, so nothing is holding anything else up. You take one tool and the other seven do not move.

Slots, not holes

Most racks drill a row of round holes at one fixed size, and then your fat old wooden spade shaft will not go in while the thin broom pole rattles about. This one uses two open steel grids instead. Anything from a slim plastic pole to a chunky hickory shaft drops straight through the same opening — and passes through both grids on the way down, so it is held at two heights and stands dead upright instead of leaning. D-handles simply rest across the top grid. Small J-hooks along the edges take the shears, the gloves, the twine and the hose nozzle.

Under two feet square, about desk height

This is the number that decides it, so here it is plainly. The rack stands 29.5 in (74.9 cm) tall — about the height of a desk — and its base covers 16.9 in (42.9 cm) across the front by 19.6 in (49.8 cm) front to back. That is roughly two and a third square feet of floor.

Because it stacks the storage upward rather than along a wall, a corner that was three feet of leaning clutter becomes one small square you can walk past. Your tools stick up well above the frame, so measure the floor space rather than the ceiling.

The mud stays in the tray

Blades go down into a deep steel tray with a raised lip and a punched floor, not onto your shed boards. Come back filthy, drop the spade in wet, and the soil that dries off it stays in one metal box you can lift out a trowel-full at a time — instead of becoming the layer of grit you stand in every time you go looking for something.

Steady on a floor that never was level

Shed boards sag. Garage slabs fall away to the door. That is why free-standing racks rock. Every leg on this one ends in a threaded foot that screws up or down, so you take the wobble out in about a minute with your fingers and it stays put.

Two habits do the rest, and they are worth knowing before it arrives: put the heavy blades low in the base tray rather than hanging weight high, and stand it against a wall rather than out in the open. A loaded tool rack carries most of its weight at the top by nature — that is the tools, not the frame.

What you get

• One rack. The tools, hose and blower in the photographs show it in use and are not included
• Black-coated steel frame, bolted at the joints
• Three tiers: two open wire grids for long handles, plus the base tray
• J-hooks along the grid edges for small gear
• A lower side shelf and a curved hanger arm for a coiled hose
• Deep punched-steel base tray with a raised lip
• Threaded levelling feet on every leg — no wheels
• 29.5 in (74.9 cm) tall · 16.9 in (42.9 cm) across · 19.6 in (49.8 cm) front to back

Not only for the garden

The same tower sorts a garage of yard tools, a workshop of long-handled gear, a utility room of mops and brooms and a vacuum hose, or the back of a van. Anywhere a row of handles is currently leaning in a corner waiting to fall over.

Frequently asked questions

How much floor does it actually take?

16.9 in (42.9 cm) across the front by 19.6 in (49.8 cm) front to back, and it stands 29.5 in (74.9 cm) tall. Just under two feet square, and about desk height.

Will my thick wooden handles fit?

The tiers are open grids rather than fixed round holes, so handles of different thicknesses go through the same slots — a heavy wooden spade shaft and a slim broom pole side by side.

Does it have wheels?

No. Every leg ends in a threaded foot that screws up or down to level the rack on an uneven floor. There are no castors and no wheel kit — this one is designed to stand still.

Does it need fixing to the wall?

No, it is free-standing. Load the heavy blades low in the base tray and stand it against a wall, and it stays where you put it.

Does it need assembling?

Yes. It is a bolt-together steel frame rather than a welded one-piece — you can see the bolt heads at the joints in the photographs.

Can it live outside?

Keep it under cover — a shed, a garage, a carport or a covered patio. Any coated steel rack left standing in the rain will corrode at the base eventually.

Will it take a leaf blower or a strimmer?

Straight-shafted powered tools sit in the grid slots, and the lower side shelf takes a blower or a bulkier body. Measure a wide guard or a big housing before assuming it drops in.

How many tools does it hold?

That depends on how thick your handles are, which is rather the point of an open grid. In practice a typical shed's worth — the long-handled tools standing in the slots, the small gear hanging off the hooks and the hose coiled on the side arm.